Start with the layer that has failed
A raised bubble or lifting edge needs an investigation of the interface that has failed. The wearing finish may have separated from the elastic layer, the full surface may have detached from the base, or weak material may have broken within a layer. Establishing that location helps the technician choose where preparation and repair must begin.
Restrict access to raised or loose areas that could create a trip hazard. Have the responsible technician choose representative investigation points and agree how any trial opening will be repaired. Record what remains attached on each side of the separation.
| Observed separation | What to examine at the opening |
|---|---|
| Finish detached from the elastic layer | Condition and preparation of the exposed elastic surface |
| Complete surface lifted from the base | Bond line primer condition and supporting substrate |
| Material broken within a layer | Strength and condition of the material remaining below |
| Repeated lifting near an edge or water route | Entry paths local detailing and extent of the affected interface |

Check how water reaches the construction
A surface that looks dry can still have moisture within the construction. Investigate nearby drains, low areas, open edges, cracks and water entering from surrounding ground. Where relevant, the inspection should also consider moisture moving upward through the base. Record the test method and the location of each measurement.
The selected coating or primer has its own substrate requirements. Use its current application instructions to decide whether the base is suitable. A waiting period after rain cannot establish moisture condition on its own. If water continues to enter below the repair, address that route as part of the proposed work.
Inspect the surface that the repair will bond to
Adhesion depends on a sound and properly prepared surface. Loose particles, dust, oil, biological growth and weak old coatings can interfere with the next layer. Removing a loose patch may reveal that the material underneath also needs treatment. Define the repair boundary around sound material after investigation.
Ask the installer to describe preparation, cleaning and the proposed primer for the exposed substrate. The method should suit the existing track and the new materials. A stronger topcoat cannot restore the strength of a crumbling base or create a reliable bond through contamination.
Review the original application sequence
Collect the available component names, batch details, mixing records and installation dates. Check whether the problem follows a daily work boundary, a particular material batch or an area repaired previously. These patterns can help direct testing and comparison.
For polyurethane layers, the application conditions and time between coats matter. Some materials use moisture to cure, while others depend on accurately mixed components. Direct rain, condensation, an unsuitable primer or an exceeded recoating interval can affect the result. The observations need to be assessed against the instructions for the actual products used.
Use a repair trial to check compatibility
Before extending a proposed repair across the track, agree a representative trial area. It should include the proposed preparation, primer and complete repair build. Record the existing layers, the materials applied and the conditions during application.
Have the responsible technician define the adhesion checks, assessment timing and acceptance criteria. CONICA's published CONIPUR 72 primer information, for example, requires preliminary adhesion testing for its stated applications. This illustrates the importance of checking the actual combination of old surface and repair material. Obtain the corresponding requirements for the system you purchase.
Define the repair boundary around a sound interface
Have the technician identify sound material around and below the affected area. Record how the failed layer will be removed, how exposed surfaces will be prepared and which compatible components will rebuild the local construction. Check transitions so the completed patch joins the retained surface at a suitable level.
If a trial opening reveals wider loss of bond, record the additional extent before extending the repair. A surface patch is viable only where the retained construction can support the proposed repair. Refer widespread or deeper failures for a broader condition assessment.
Assess the trial at the same interface that failed
Use the representative trial to check the proposed combination of preparation, primer and replacement layers. The technician should specify the test method, assessment timing and acceptance criteria for that repair. Record where separation occurs during any test so the result addresses the interface under investigation.
Retain the material identification, site conditions and observations from the trial. After the repair is released for use, inspect its edges and the surrounding retained surface during routine care. For a decision about broader renewal, use the condition-assessment guide below.
Send the defect information for a material discussion
USAWEGI can discuss running track materials, compatible system options and installation guidance with your project team. Send the location, affected area, overall track photographs, close views of exposed layers, existing material information and the available inspection results.
Tell us whether you need local repair materials or a proposal for wider renewal. We can organize a material discussion around the identified construction and the work your local technician recommends.

