Professional IAAF Certified 13mm Prefabricated Rubber Running Track - No Pour System with Installation Service

01 / FACTORY-MADE 13MM RUBBER ROLLS

13mm Prefabricated Rubber Running Track

A finished rubber surface, manufactured before it reaches your site. ASR-PR1 is supplied as flexible rubber rolls with a textured running face and a profiled underside. The wearing surface and its thickness are formed in the factory, rather than built up as a wet rubber layer on the track.

This gives the project a defined roll product to sample, lay out and order. Review the actual face texture, underside and 13mm construction together when selecting the surface.

02 / NO-POUR SURFACE INSTALLATION

Unroll, Position and Bond the Finished Surface

The No-Pour system uses factory-made rubber sheet bonded onto a prepared base. The site team sets out the rolls, applies the compatible adhesive, positions each length and finishes the adjoining seams. There is no on-site pouring of the rubber wearing layer.

Less surface forming on site; a clear roll-by-roll installation sequence. Adhesive work, base preparation, joint finishing and curing are still necessary. A sound, dry and level base is essential to the bond and the finished track.

03 / INSTALLATION SERVICE

Material Supply with a Planned Installation Scope

The roll surface, adhesive, roll layout and installation method work as one system. Our project support can cover material selection, laying guidance and installation arrangements for the agreed location and scope.

Before work starts, the quotation identifies responsibility for base acceptance, adhesive supply, roll laying, seams and lane markings. This helps the buyer appoint the right site team and plan the handover around a complete installed surface.

See the Surface, Backing and Colour Options

The textured face is the exposed running surface. The profiled underside is part of the roll construction and sits against the specified adhesive system. Red and blue samples below show real material finishes; choose the production colour against an approved sample.

ASR-PR1 Product and Supply Details

From Prepared Base to Joined Track Rolls

A clear installation sequence keeps the factory-made surface and site workmanship aligned. The photos show adhesive application, positioning and seam work from our material archive.

1. Apply the adhesive

Prepare the base and spread the specified adhesive over the planned working area. Follow its application and open-time instructions.

2. Set the rubber rolls

Position the rolls to the approved layout, keeping direction, alignment and adjoining edges consistent.

3. Finish the joints

Join adjacent lengths and complete the specified seam, perimeter and bond checks before marking and handover.

A Complete Track Layout, Finished for Use

Roll direction, curved sections, perimeter interfaces and lane markings are planned together. The completed surfaces below show how the rubber track sits alongside the infield and surrounding sports areas.

Technical Documents and Project Handover

Product documentation supports the material decision alongside the physical sample. For a specification-led project, request the ASR-PR1 datasheet and the applicable WA/IAAF documentation, with the product name and scope identified. Product certification and any required testing of the installed facility should be addressed separately.

Supply and installation documents should identify the roll quantity, colour, adhesive, layout and agreed site work. At handover, inspect the surface condition, seams, edges and markings, and provide the relevant use and care instructions.

Questions About the No-Pour Roll System

Does No-Pour mean no adhesive or curing?

No. It describes the prefabricated rubber wearing surface. The rolls still need compatible adhesive, seam work and the specified curing period.

Can the rolls be installed over an existing track?

The existing substrate must be assessed for its condition, bond, levels, moisture and compatibility. Unsound material and base defects need treatment before the new roll system is installed.

What does the installation service include?

The project quotation defines whether the order includes technical guidance, installation labour, adhesive and consumables, lane marking or other site work. The service arrangement depends on the location and agreed responsibilities.

What should I send for a quotation?

Send the track plan, measured area, project location, base photos, required colours and target schedule. State whether you need material supply, guidance or installation so the quotation covers the right scope.

Plan Your 13mm Prefabricated Track Project

Share your drawings and site information through the product inquiry form. We will review the roll surface, colour, material quantity and installation scope for your project.